Applies to VoipNow 3 and higher!

This article explains how to set up a Cisco/Linksys SPA phone terminal that will be used with the VoipNow phone provisioning module. These recommendations apply to the following phone devices:

Also, you can follow these instructions even if you're doing this for the very first time.  

Phone installation

Assuming that your phone is reset to the default configuration:

  1. Assemble the power adapter. After plugging the adapter in a wall outlet, push the power jack into the power socket on the bottom of the phone base unit.
  2. Connect one end of the RJ-7 cable to the RJ-7 socket on the back of the phone and the other end of the handset cord.
  3. Connect the standard RJ-45 Ethernet Cable to the phone LAN (or SW, depending on model) port on the bottom of the phone.
  4. Connect the other end of the cable to an Ethernet switch or router.

For more information on the physical installation, check the phone terminal's user guides provided by the vendor.

Configuration of phone network parameters

If the administrator has set up DHCP, the phone will automatically get its network parameters from the DHCP server. At this point, you can skip to the Configuration of phone provisioning parameters section.

If the administrator has not set up DHCP, you must assign a static IP address to the phone. To do this, take the following steps: 

STEP 1: Press the Setup key on the phone pad. The Setup menu is displayed on the LCD screen. Use the up and down arrow keys to navigate through the menu.

STEP 2: Navigate to the Network entry. Press the key corresponding to the select option on the screen (i.e. the left key under the LCD screen). The Network menu will be displayed on the LCD screen.

STEP 3: Press the key corresponding to the edit (or select on newer phones) option on the screen.

STEP 4: Press the key corresponding to the y/n option until No is displayed on the LCD screen. On SPA 500 series, navigate to Wan ConnectionType.

STEP 5: Press the key corresponding to the ok option on the screen. The settings will be saved and you will be returned to the Network menu. On SPA 500 series, press the option key until you get StaticIP on the screen. Press the save soft key.

STEP 6: Navigate to the Non-DHCPIP Address entry and press edit.

STEP 7: Using the phone keypad, enter the IP address assigned to the phone. This address must be provided by the VoipNow system administrator. Use the * (star) key to type . (dot).

STEP 8: Press OK to save the settings and return to the Network menu.

STEP 9: Repeat steps 6, 7, 8 for each of the following entries: Non-DHCPSubnetMask, Non-DHCPDefaultRoute, Non-DHCPDNS1, Non-DHCPDNS2.

STEP 10: Press the key corresponding to the save option in the Network menu in order to save your network settings and go back to the Setup menu.

STEP 11: Next, select the Restart entry. Press the key corresponding to select and then press OK.

Configuration of phone provisioning parameters

STEP 1: Open a web browser and type http://<Non-DHCPIP Address>/admin/advanced in the address bar. Assuming that everything was configured correctly, the browser should display the phone web interface.

You can find the IP address assigned to your phone by pressing the Setup button. Use the down arrow key to navigate to the Network entry. Press the key corresponding to select and locate the CurrentIP entry.

STEP 2: Configure the provisioning feature by following the next steps:

At this point, you should be able to make your first phone call.


If your administrator lets you provide the link for the phone yourself, then you should take the following steps: 

STEP 1: Log in to the VoipNow web interface with your extension account.

STEP 2: Click the Provisioning and SIP icon available in the Telephony section.

STEP 3: Customize the following fields taking into consideration the explanations below. 


Device Information

Device Settings

SIP Preferences

STEP 4: Click OK to save the data. The provisioning link will be displayed at the top of the screen.

Related articles